S-15 - Solar Thermal Systems for Swimming Pool, Spas and Hot Tubs.

S-15.1   Water Chemistry.

Where water from a swimming pool, spa or hot tub is heated by way of circulation through solar collectors, the chemistry of such water shall comply with the requirements of Section S-15.2 and shall be filtered in accordance with Sections S-15.3 and S-15.3.1 of this Code.

(Ord. 2016-0055 § 20, 2016: Ord. 2013-0050 § 22, 2013.)

S-15.2   Parameters.

Parameters for chemicals used within a swimming pool, spa, or hot tub shall be in accordance with Table S-15.2.

(Ord. 2016-0055 § 20, 2016.)

TABLE S-15.2
WATER CHEMISTRY

PARAMETER	ACCEPTABLE RANGE
Calcium hardness	200 - 400 parts per million (ppm)
Langelier Saturation Index	0 (+ or - 0.3 acceptable)
pH	7.2 - 7.8
TDS	< 1500 ppm
Total alkalinity	80 - 120 ppm

 

For SI Units: 1 part per million = 1 mg/L.

(Ord. 2013-0050 § 22, 2013.)

S-15.3   Filter.

A filter shall be provided to remove debris from the water entering the solar loop.

EXCEPTION: A solar swimming pool, spa, or hot tub heating system with a heat exchanger.

(Ord. 2013-0050 § 22, 2013.)

S-15.3.1   Location.

A filter shall be located upstream of a pump used to direct water to solar collectors.

(Ord. 2013-0050 § 22, 2013.)

S-15.4   Corrosion Resistant.

Glazed solar collectors made of copper shall not be used for solar pool, spa, or hot tub heating.

EXCEPTION: Where a heat exchanger is provided between the collector circuit and the swimming pool, spa, or hot tub water.

(Ord. 2013-0050 § 22, 2013.)

S-16   Certificate of Compliance.

Upon completion of the solar thermal energy system, the permittee shall sign a Certificate of Compliance with this Code.

The Certificate of Compliance shall also list the following information:

(1)

Type of freeze protection;

(2)

Mixing valve setting degrees Fahrenheit (º F);

(3)

Subsystem working pressure (if applicable) psi;

(4)

Subsystem test pressure (if applicable) psi;

(5)

Heat exchange make and model number (if applicable);

(6)

Circulating pump over temperature protection shut-off setting degrees Fahrenheit (º F) for one-tank systems where the water heater controls utilize fusible-link type over temperature protection.

This Certificate shall be posted in a conspicuous location at or near the water heater.

(Ord. 2016-0055 § 20, 2016; Ord. 2013-0050 § 22, 2013.)

S-17   Referenced Standards.

The standards listed in Table S-17 are intended for use in the design, testing, and installation of materials, devices, appliances, and equipment regulated by this Chapter.

TABLE S-17
REFERENCED STANDARDS

STANDARD NUMBER	STANDARD TITLE	APPLICATION
AHRI 870-2005*	Performance Rating of Direct GeoExchange Heat Pumps	Equipment
ASCE 25-2006*	Earthquake-Actuated Automatic Gas Shutoff Devices	Fuel Gas
ASHRAE 34-2013*	Designation and Safety Classification of Refrigerants	Refrigerant Classifications
ASHRAE 90.1-2013*	Energy Standard for Buildings Except Low-Rise Residential Buildings	Energy
ASHRAE 93-2010 (RA2014)*	Methods of Testing to Determine the Thermal Performance of Solar Collectors	Testing
ASHRAE 95-1981 (RA1987)*	Methods of Testing to Determine the Thermal Performance of Solar Domestic Water Heating Systems	Testing
ASHRAE 96-1980 (RA1989)*	Thermal Performance of Unglazed Flat-Plate Liquid-Type Solar Collectors	Testing, Collector
ASME A13.1-2007 (R2013)*	Scheme for the Identification of Piping Systems	Piping
ASME A112.18.1-2012/CSA B125.1-2012	Plumbing Supply Fittings	Fittings
ASME A112.18.2-2011/CSA B125.2-2011	Plumbing Waste Fittings	Fittings
ASME A112.18.6-2009/CSA B125.6-2009 (R2014)*	Flexible Water Connectors	Piping
ASME B1.20.1-2013*	Pipe Threads, General Purpose (Inch)	Joints
ASME B16.3-2011*	Malleable Iron Threaded Fittings: Classes 150 and 300	Fittings
ASME B16.5-2013*	Pipe Flanges and Flanged Fittings: NPS ½ through NPS 24 Metric/Inch	Fittings
ASME B16.9-2012*	Factory-Made Wrought Buttwelding Fittings	Fittings
ASME B16.11-2011*	Forged Fittings, Socket-Welding and Threaded	Fittings
ASME B16.12-2009*	Cast Iron Threaded Drainage Fittings	Fittings
ASME B16.15-2013*	Cast Copper Alloy Threaded Fittings: Classes 125 and 250	Fittings
ASME B16.18-2012*	Cast Copper Alloy Solder Joint Pressure Fittings	Fittings
ASME B16.21-2011*	Nonmetallic Flat Gaskets for Pipe Flanges	Joints
ASME B16.22-2013*	Wrought Copper and Copper Alloy Solder-Joint Pressure Fittings	Fittings
ASME B16.23-2011*	Cast Copper Alloy Solder Joint Drainage Fittings: DWV	Fittings
ASME B16.24-2011*	Cast Copper Alloy Pipe Flanges and Flanged Fittings: Classes 150, 300, 600, 900, 1500, and 2500	Fittings
ASME B16.26-2013*	Cast Copper Alloy Fittings for Flared Copper Tubes	Fittings
ASME B16.29-2012*	Wrought Copper and Wrought Copper Alloy Solder-Joint Drainage Fittings - DWV	Fittings
ASME B16.33-2012*	Manually Operated Metallic Gas Valves for Use in Gas Piping Systems Up to 175 psi (Sizes NPS 1/2 - NPS 2)	Valves
ASME B16.34-2013*	Valves - Flanged, Threaded, and Welding End	Valves
ASME B16.47-2011*	Large Diameter Steel Flanges: NPS 26 Through NPS 60 Metric/Inch	Fittings
ASME B16.51-2013*	Copper and Copper Alloy Press-Connect Pressure Fittings	Fittings
ASME BPVC Section IV-2013*	Rules for Construction of Heating Boilers	Miscellaneous
ASME BPVC Section VIII- 2013*	Rules for Construction of Pressure Vessels Division 1	Miscellaneous
ASME BPVC Section IX-2013*	Welding, Brazing, and Fusing Qualifications	Certification
ASME BPVC Section X-2013*	Fiber-Reinforced Plastic Pressure Vessels	Pressure Vessel Construction, Pressure Vessels
ASME SA194-2013*	Carbon and Alloy Steel Nuts for Bolts for High-Pressure or High-Temperature Service, or Both	Mounting
ASSE 1001-2008*	Atmospheric Type Vacuum Breakers	Backflow Protection
ASSE 1010-2004*	Water Hammer Arresters	Water Supply Component
ASSE 1017-2009*	Temperature Actuated Mixing Valves for Hot Water Distribution Systems	Valves
ASSE 1018-2001*	Trap Seal Primer Valves-Potable Water Supplied	Valves
ASSE 1061-2011*	Push-Fit Fittings	Fittings
ASSE 1079-2012	Dielectric Pipe Unions	Joints
ASTM A53/A53M-2012	Pipe, Steel, Black and Hot-Dipped, Zinc-Coated, Welded and Seamless	Piping, Ferrous
ASTM A74-2013a	Cast Iron Soil Pipe and Fittings	Piping, Ferrous
ASTM A106/A106M-2014	Seamless Carbon Steel Pipe for High-Temperature Service	Piping, Ferrous
ASTM A126-2004 (R2014)	Gray Iron Castings for Valves, Flanges, and Pipe Fittings	Piping, Ferrous
ASTM A254/A254M-2012	Copper-Brazed Steel Tubing	Piping, Ferrous
ASTM A269/A269M-2014 e1	Seamless and Welded Austenitic Stainless Steel Tubing for General Service	Piping, Ferrous
ASTM A312/A312M-2014	Seamless, Welded, and Heavily Cold Worked Austenitic Stainless Steel Pipes	Piping, Ferrous
ASTM A377-2003 (R2008) e1	Ductile-Iron Pressure Pipe	Piping, Ferrous
ASTM A420/A420M-2013	Piping Fittings of Wrought Carbon Steel and Alloy Steel for Low-Temperature Service	Fittings
ASTM A518/A518M-1999 (R2012)	Corrosion-Resistant High-Silicon Iron Castings	Piping, Ferrous
ASTM A733-2013	Welded and Seamless Carbon Steel and Austenitic Stainless Steel Pipe Nipples	Piping, Ferrous
ASTM A861-2004 (R2013)	High-Silicon Iron Pipe and Fittings (Note 1)	Piping, Ferrous
ASTM B32-2008	Solder Metal (Note 2)	Joints
ASTM B42-2010	Seamless Copper Pipe, Standard Sizes	Piping, Copper Alloy
ASTM B43-2014	Seamless Red Brass Pipe, Standard Sizes	Piping, Copper Alloy
ASTM B75/B75M-2011	Seamless Copper Tube	Piping, Copper Alloy
ASTM B88-2009	Seamless Copper Water Tube	Piping, Copper Alloy
ASTM B135-2010	Seamless Brass Tube	Piping, Copper Alloy
ASTM B251-2010	General Requirements for Wrought Seamless Copper and Copper-Alloy Tube	Piping, Copper Alloy
ASTM B280-2013	Seamless Copper Tube for Air Conditioning and Refrigeration Field Service	Piping, Ferrous
ASTM B302-2012	Threadless Copper Pipe, Standard Sizes	Piping, Copper Alloy
ASTM B306-2013	Copper Drainage Tube (DWV)	Piping, Copper Alloy
ASTM B447-2012a	Welded Copper Tube	Piping, Copper Alloy
ASTM B584-2014	Copper Alloy Sand Castings for General Applications (Note 3)	Piping, Copper Alloy
ASTM B587-2012	Welded Brass Tube	Piping, Copper Alloy
ASTM B687-1999 (R2011)	Brass, Copper, and Chromium-Plated Pipe Nipples	Piping, Copper Alloy
ASTM B813-2010	Liquid and Paste Fluxes for Soldering of Copper and Copper Alloy Tube	Joints
ASTM B828-2002 (R2010)	Making Capillary Joints by Soldering of Copper and Copper Alloy Tube and Fittings	Joints
ASTM C411-2011	Hot-Surface Performance of High-Temperature Thermal Insulation	Block Board, Cracking, Delamination, Hot- Surface Performance, Pipe Thermal Insulation, Surface Analysis- Building, Temperature Tests- Insulation, Thermal Insulating Materials
ASTM C425-2004 (R2013)	Compression Joints for Vitrified Clay Pipe and Fittings	Joints
ASTM C443-2012	Joints for Concrete Pipe and Manholes, Using Rubber Gaskets	Joints
ASTM C564- 2014	Rubber Gaskets for Cast Iron Soil Pipe and Fittings	Joints
ASTM C700-2013	Vitrified Clay Pipe, Extra Strength, Standard Strength, and Perforated	Piping, Non-Metallic
ASTM C1277-2014	Shielded Couplings Joining Hubless Cast Iron Soil Pipe and Fittings	Joints
ASTM D56-2005 (R2010)	Flash Point by the Tag Closed Cup Tester	Testing
ASTM D93-2013e1	Flash Point by Pensky-Martens Closed Cup Tester	Testing
ASTM D635-2010	Rate of Burning and/or Extent and Time of Burning of Plastics in a Horizontal Position	Testing
ASTM D1527-1999 (R2005)*	Acrylonitrile-Butadiene-Styrene (ABS) Plastic Pipe, Schedules 40 and 80	Piping, Plastic
ASTM D1693-2013	Environmental Stress-Cracking of Ethylene Plastics	Piping, Plastic
ASTM D1785-2012*	Poly (Vinyl Chloride) (PVC) Plastic Pipe, Schedules 40, 80, and 120	Piping, Plastic
ASTM D2235-2004 (R2011)*	Solvent Cement for Acrylonitrile-Butadiene-Styrene (ABS) Plastic Pipe and Fittings	Joints
ASTM D2241-2009*	Poly (Vinyl Chloride) (PVC) Pressure-Rated Pipe (SDR Series)	Piping, Plastic
ASTM D2464-2013*	Threaded Poly (Vinyl Chloride) (PVC) Plastic Pipe Fittings, Schedule 80 (Note 1)	Fittings
ASTM D2466-2013*	Poly (Vinyl Chloride) (PVC) Plastic Pipe Fittings, Schedule 40 (Note 1)	Fittings
ASTM D2467-2013a*	Poly (Vinyl Chloride) (PVC) Plastic Pipe Fittings, Schedule 80 (Note 1)	Fittings
ASTM D2513-2014*	Polyethylene (PE) Gas Pressure Pipe, Tubing, and Fittings (Note 1)	Piping, Plastic
ASTM D2564-2012*	Solvent Cements for Poly (Vinyl Chloride) (PVC) Plastic Piping Systems	Joints
ASTM D2609-2002 (R2008)*	Plastic Insert Fittings for Polyethylene (PE) Plastic Pipe (Note 1)	Fittings
ASTM D2672-1996a (R2009)*	Joints for IPS PVC Pipe Using Solvent Cement	Joints
ASTM D2683-2010 e3 *	Socket-Type Polyethylene Fittings for Outside Diameter- Controlled Polyethylene Pipe and Tubing	Fittings
ASTM D2837-2013 e1	Obtaining Hydrostatic Design Basis for Thermoplastic Pipe Materials or Pressure Design Basis for Thermoplastic Pipe Products	Piping, Plastic
ASTM D2846/D2846M-2009b e1 *	Chlorinated Poly (Vinyl Chloride) (CPVC) Plastic Hot- and Cold-Water Distribution Systems	Piping, Plastic
ASTM D2855-1996 (R2010)*	Making Solvent-Cemented Joints with Poly (Vinyl Chloride) (PVC) Pipe and Fittings	Joints
ASTM D3035-2014*	Polyethylene (PE) Plastic Pipe (DR-PR) Based on Controlled Outside Diameter	Piping, Plastic
ASTM D3139-1998 (R2011)*	Joints for Plastic Pressure Pipes Using Flexible Elastomeric Seals	Joints
ASTM D3261-2012 e1 *	Butt Heat Fusion Polyethylene (PE) Plastic Fittings for Polyethylene (PE) Plastic Pipe and Tubing	Fittings
ASTM D3278-1996 (R2011)	Flash Point of Liquids by Small Scale Closed-Cup Apparatus	Testing
ASTM D3350-2012 e1	Polyethylene Plastics Pipe and Fittings Materials	Piping, Plastic
ASTM E84-2014*	Surface Burning Characteristics of Building Materials	Miscellaneous
ASTM E136-2012*	Behavior of Materials in a Vertical Tube Furnace at 750°C	Furnace
ASTM E2231-2014*	Specimen Preparation and Mounting of Pipe and Duct Insulation Materials to Assess Surface Burning Characteristics	Miscellaneous
ASTM F437-2009*	Threaded Chlorinated Poly (Vinyl Chloride) (CPVC) Plastic Pipe Fittings, Schedule 80	Fittings
ASTM F438-2009*	Socket-Type Chlorinated Poly (Vinyl Chloride) (CPVC) Plastic Pipe Fittings, Schedule 40	Fittings
ASTM F439-2013*	Chlorinated Poly (Vinyl Chloride) (CPVC) Plastic Pipe Fittings, Schedule 80	Fittings
ASTM F441/F441M-2013 e1 *	Chlorinated Poly (Vinyl Chloride) (CPVC) Plastic Pipe, Schedules 40 and 80	Piping, Plastic
ASTM F442/F442M-2013 e1 *	Chlorinated Poly (Vinyl Chloride) (CPVC) Plastic Pipe (SDR- PR)	Piping, Plastic
ASTM F480-2014*	Thermoplastic Well Casing Pipe and Couplings Made in Stand- ard Dimension Ratios (SDR), SCH 40 and SCH 80	Piping, Plastic
ASTM F493-2010*	Solvent Cements for Chlorinated Poly (Vinyl Chloride) (CPVC) Plastic Pipe and Fittings	Joints
ASTM F628-2012 e1 *	Acrylonitrile-Butadiene-Styrene (ABS) Schedule 40 Plastic Drain, Waste, and Vent Pipe with a Cellular Core (Note 1)	Piping, Plastic
ASTM F656-2010*	Primers for Use in Solvent Cement Joints of Poly (Vinyl Chloride) (PVC) Plastic Pipe and Fittings	Joints
ASTM F714-2013*	Polyethylene (PE) Plastic Pipe (DR-PR) Based on Outside Diameter	Piping, Plastic
ASTM F876-2013a*	Crosslinked Polyethylene (PEX) Tubing	Piping, Plastic
ASTM F877-2011a*	Crosslinked Polyethylene (PEX) Plastic Hot- and Cold-Water Distribution Systems	Piping, Plastic
ASTM F891-2010*	Coextruded Poly(Vinyl Chloride) (PVC) Plastic Pipe with a Cellular Core	Piping, Plastic
ASTM F1055-2013*	Electrofusion Type Polyethylene Fittings for Outside Diameter Controlled Polyethylene and Crosslinked Polyethylene (PEX) Pipe and Tubing	Fittings
ASTM F1281-2011*	Crosslinked Polyethylene/Aluminum/Crosslinked Polyethylene (PEX-AL-PEX) Pressure Pipe	Piping, Plastic
ASTM F1282-2010*	Polyethylene/Aluminum/Polyethylene (PE-AL-PE) Composite Pressure Pipe	Piping, Plastic
ASTM F1807-2013a*	Metal Insert Fittings Utilizing a Copper Crimp Ring for SDR9 Cross-linked Polyethylene (PEX) Tubing and SDR9 Polyethylene of Raised Temperature (PE-RT) Tubing	Fittings
ASTM F1960-2012*	Cold Expansion Fittings with PEX Reinforcing Rings for Use with Cross-linked Polyethylene (PEX) Tubing	Fittings
ASTM F1961-2009*	Metal Mechanical Cold Flare Compression Fittings with Disc Spring for Crosslinked Polyethylene (PEX) Tubing	Fittings
ASTM F1970-2012 e1 *	Special Engineered Fittings, Appurtenances or Valves for Use in Poly (Vinyl Chloride) (PVC) or Chlorinated Poly (Vinyl Chloride) (CPVC) Systems	Piping, Plastic
ASTM F1974-2009*	Metal Insert Fittings for Polyethylene/Aluminum/Polyethylene and Crosslinked Polyethylene/Aluminum/Crosslinked Polyethylene Composite Pressure Pipe	Fittings
ASTM F2080-2012*	Cold-Expansion Fittings with Metal Compression-Sleeves for Cross-Linked Polyethylene (PEX) Pipe	Fittings
ASTM F2159-2011*	Plastic Insert Fittings Utilizing a Copper Crimp Ring for SDR9 Cross-linked Polyethylene (PEX) Tubing and SDR9 Polyethylene of Raised Temperature (PE-RT) Tubing	Joints
ASTM F2262-2009*	Crosslinked Polyethylene/Aluminum/Crosslinked Polyethylene Tubing OD Controlled SDR9	Piping, Plastic
ASTM F2389-2010	Pressure-Rated Polypropylene (PP) Piping Systems	Piping, Plastic
ASTM F2434-2009*	Metal Insert Fittings Utilizing a Copper Crimp Ring for SDR9 Cross-linked Polyethylene (PEX) Tubing and SDR9 Cross- linked Polyethylene/Aluminum/Cross-linked Polyethylene (PEX-AL-PEX) Tubing	Pipe Fittings
ASTM F2620-2013*	Standard Practice for Heat Fusion Joining of Polyethylene Pipe and Fittings	Joints
ASTM F2623-2008*	Polyethylene of Raised Temperature (PE-RT) SDR9 Tubing	Piping, Plastic
ASTM F2735-2009*	Plastic Insert Fittings for SDR9 Cross-linked Polyethylene (PEX) and Polyethylene of Raised Temperature (PE-RT) Tubing	Fittings
ASTM F2769-2010*	Polyethylene of Raised Temperature (PE-RT) Plastic Hot and Cold-Water Tubing and Distribution Systems	Piping and Fittings, Plastic
AWS A5.8M/A5.8-2011*	Filler Metals for Brazing and Braze Welding	Joints
AWS B2.2/B2.2M-2010*	Brazing Procedure and Performance Qualification	Certification
AWWA C110-2012*	Ductile-Iron and Gray-Iron Fittings	Fittings
AWWA C111-2012*	Rubber-Gasket Joints for Ductile-Iron Pressure Pipe and Fittings (same as ANSI A21.11)	Joints
AWWA C115-2011*	Flanged Ductile-Iron Pipe with Ductile-Iron or Gray-Iron Threaded Flanges	Piping
AWWA C151-2009*	Ductile-Iron Pipe, Centrifugally Cast	Piping, Ferrous
AWWA C153-2011*	Ductile-Iron Compact Fittings	Fittings
AWWA C203-2008*	Coal-Tar Protective Coatings and Linings for Steel Water Pipelines-Enamel and Tape-Hot Applied	Miscellaneous
AWWA C213-2007*	Fusion-Bonded Epoxy Coating for the Interior and Exterior of Steel Water Pipelines	Miscellaneous
AWWA C215-2010*	Extruded Polyolefin Coatings for the Exterior of Steel Water Pipeline	Miscellaneous
AWWA C500-2009*	Metal-Seated Gate Valves for Water Supply Service	Valves
AWWA C507-2011*	Ball Valves, 6 in. through 60 in. (150 mm through 1,500 mm)	Valves
BS EN 12975-1-2006 (R2010)	Thermal Solar Systems and Components - Solar Collectors - Part 1: General Requirements	Collector
BS EN 12975-2-2006	Thermal Solar Systems and Components - Solar Collectors - Part 2: Test Methods	Collector
BS EN 12976-1-2006	Thermal Solar Systems and Components - Factory Made Systems - Part 1: General Requirements	Solar System
BS EN 12976-2-2006	Thermal Solar Systems and Components - Factory Made Systems - Part 2: Test Methods	Solar System
BS EN ISO 9488-2000	Solar Energy - Vocabulary	Miscellaneous
CSA B137.1-2013	Polyethylene (PE) Pipe, Tubing, and Fittings for Cold-Water Pressure Services	Piping, Plastic
CSA B137.5-2013	Crosslinked Polyethylene (PEX) Tubing Systems for Pressure Applications	Piping, Plastic
CSA B137.9-2013	Polyethylene/Aluminum/Polyethylene (PE-AL-PE) Composite Pressure-Pipe Systems	Piping, Plastic
CSA B137.10-2013	Crosslinked Polyethylene/Aluminum/Crosslinked Polyethylene (PEX-AL-PEX) Composite Pressure-Pipe Systems	Piping, Plastic
CSA B137.11-2013	Polypropylene (PP-R) Pipe and Fittings for Pressure Applications	Piping, Plastic
CSA Z21.10.1-2013*	Gas Water Heaters -Volume I, Storage Water Heaters with Input Ratings of 75,000 Btu Per Hour or Less (same as CSA 4.1)	Fuel Gas, Appliances
CSA Z21.10.3-2013*	Gas-Fired Water Heaters -Volume III, Storage Water Heaters with Input Ratings Above 75,000 Btu Per Hour, Circulating and Instantaneous (same as CSA 4.3)	Fuel Gas, Appliances
CSA Z21.13-2014*	Gas-Fired Low Pressure Steam and Hot Water Boilers (same as CSA 4.9)	Fuel Gas, Appliances
CSA Z21.22b-2001 (R2008)*	Relief Valves for Hot Water Supply Systems (same as CSA 4.4b)	Valves
CSA Z21.24a-2009 (R2011)*	Connectors for Gas Appliances (same as CSA 6.10a)	Fuel Gas
CSA Z21.56-2014*	Gas-Fired Pool Heaters (same as CSA 4.7)	Fuel Gas, Swimming Pools and Spas, and Hot Tubs
IAPMO IS 8-2006	PVC Cold Water Building Supply and Yard Piping	Piping, Plastic
IAPMO IS 13-2006	Protectively Coated Pipe	Pipe Coatings
IAPMO IS 20-2010 e1	CPVC Solvent Cemented Hot and Cold Water Distribution Systems	Piping, Plastic
IAPMO PS 25-2002	Metallic Fittings for Joining Polyethylene Pipe for Water Service and Yard Piping	Joints
IAPMO PS 64-2012a e1	Roof Pipe Flashings	Miscellaneous
IAPMO PS 72-2007 e1	Valves with Atmospheric Vacuum Breakers	Valves
IAPMO PS-117-2012a e1	Press and Nail Connections	Fittings
IEEE 937-2007	Installation and Maintenance of Lead-Acid Batteries for Photovoltaic (PV) Systems	Installation and Maintenance, Photovoltaic
IEEE 1013-2007	Sizing Lead-Acid Batteries for Stand-Alone Photovoltaic (PV) Systems	Photovoltaic, Sizing
IEEE 1361-2003*	Lead-Acid Batteries Used in Stand-Alone Photovoltaic (PV) Systems	Testing, Evaluation
IEEE 1526-2003*	Testing the Performance of Stand-Alone Photovoltaic Systems	Testing, Photovoltaic
IEEE 1547-2003	Interconnecting Distributed Resources with Electric Power Systems	Connections, Photovoltaic
IEEE 1562-2007	Array and Battery Sizing in Stand-Alone Photovoltaic (PV) Systems	Array, Battery, Photovoltaic
IEEE 1661-2007	Lead-Acid Batteries Used in Photovoltaic (PV) Hybrid Power Systems	Testing and Evaluation, Photovoltaic
MSS SP-58-2009*	Pipe Hangers and Supports - Materials, Design, Manufacture, Selection, Application, and Installation	Fuel Gas
MSS SP-80-2013	Bronze Gate, Globe, Angle, and Check Valves	Valves
NFPA 54/Z223.1-2012*	National Fuel Gas Code	Fuel Gas
NFPA 70-2014*	National Electrical Code	Electrical, Miscellaneous
NFPA 96-2014*	Ventilation Control and Fire Protection of Commercial Cooking Operations	Commercial Cooking
NFPA 262-2011*	Flame Travel and Smoke of Wires and Cables for Use in Air- Handling Spaces	Certification
NFPA 274-2013*	Test Method to Evaluate Fire Performance Characteristics of Pipe Insulation	Pipe Insulation
NGWA-01-2014*	Water Well Construction Standard	Geothermal
NSF 14-2013*	Plastic Piping System Components and Related Materials	Piping, Plastic
NSF 60-2013*	Drinking Water Treatment Chemicals-Health Effects	Backfill
NSF 61-2013*	Drinking Water System Components - Health Effects	Water Supply Components
SAE J512-1997	Automotive Tube Fittings	Fittings
SMACNA-2006*	HVAC Duct Construction Standards Metal and Flexible, 3rd edition	Ducts, Metal and Flexible
SRCC 100-2013	Solar Thermal Collectors	Collectors
SRCC 300-2013	Solar Water Heating Systems	Solar System
UL 174-2004*	Household Electric Storage Tank Water Heaters (with revisions through September 21, 2012)	Appliances
UL 181-2013*	Factory-Made Air Ducts and Air Connectors	Air Connectors, Air Ducts
UL 181A-2013*	Closure Systems for Use with Rigid Air Ducts	Air Ducts
UL 181B-2013*	Closure Systems for Use with Flexible Air Ducts and Air Connectors	Air Connectors, Air Ducts
UL 268A-2008*	Smoke Detectors for Duct Application (with revisions through September 25, 2009)	Smoke Detectors
UL 555-2006*	Fire Dampers (with revisions through November 5, 2013)	Dampers
UL 555C-2006*	Ceiling Dampers (with revisions through May 4, 2010)	Dampers
UL 555S-1999*	Smoke Dampers (with revisions through October 9, 2013)	Dampers
UL 723-2008*	Test for Surface Burning Characteristics of Building Materials (with revisions through August 12, 2013)	Miscellaneous
UL 778-2010*	Motor-Operated Water Pumps (with revisions through May 23, 2014)	Pumps
UL 834-2004*	Heating, Water Supply, and Power Boilers - Electric (with revisions through December 9, 2013)	Appliances
UL 873-2007	Temperature-Indicating and -Regulating Equipment (with revisions through August 15, 2013)	Electrical
UL 916-2007	Energy Management Equipment (with revisions through December 19, 2013)	Electrical
UL 969-1995*	Marking and Labeling System (with revisions through November 24, 2008)	Marking, Labeling
UL 1279-2010	Outline of Investigation for Solar Collectors	Electrical
UL 1453-2004*	Electric Booster and Commercial Storage Tank Water Heaters (with revisions through July 15, 2011)	Appliances
UL 1703-2002*	Flat-Plate Photovoltaic Modules and Panels (with revisions through October 25, 2013)	Electrical
UL 1741-2010	Inverters, Converters, Controllers and Interconnection System Equipment for Use With Distributed Energy Resources	Electrical
UL 1820-2004*	Fire Test of Pneumatic Tubing for Flame and Smoke Characteristics (with revisions through May 10, 2013)	Surface Burning Test, Pneumatic Tubing
UL 1887-2004*	Fire Test of Plastic Sprinkler Pipe for Visible Flame and Smoke Characteristics (with revisions through May 3, 2013)	Surface Burning Test, Fire Sprinkler Pipe
UL 2043-2013*	Fire Test for Heat and Visible Smoke Release for Discrete Products and their Accessories Installed in Air-Handling Spaces	Surface Burning Test, Discrete Products
UL 2523-2009*	Solid Fuel-Fired Hydronic Heating Appliances, Water Heaters, and Boilers (with revisions through February 8, 2013)	Appliances
UL 4703-2010	Outline of Investigation for Photovoltaic Wire	Electrical
UL 6703-2011	Outline of Investigation for Connectors for Use in Photovoltaic Systems	Electrical
UL 8703-2011	Outline of Investigation for Concentrator Photovoltaic Modules and Assemblies	Electrical
UL 60730-1 2009*	Automatic Electrical Controls for Household and Similar Use, Part 1: General Requirements (with revisions through November 13, 2013)	Electrical

 

*ANSI designated as an American National Standard.

Notes:

Although this standard is referenced in Table S17, some of the pipe, tubing, fittings, or valves included in the standard are not acceptable for use under the provisions of this Appendix.

See Section 605.1 for restrictions.

Alloy C85200 for cleanout plugs.

Standards for materials, equipment, joints and connections. Where more than one standard has been listed for the same material or method, the relevant portions of all such standards shall apply.

(Ord. 2016-0055 § 20, 2016.)

S-17.1   Abbreviations in Table S-17.

ANSI	American National Standards Institute, Inc., 25 W. 43rd Street, 4th Floor, New York, NY 10036.
ASCE	American Society of Civil Engineers, 1801 Alexander Bell Drive, Reston, VA 20191-4400.
ASHRAE	American Society of Heating, Refrigerating and Air Conditioning Engineers, Inc., 1791 Tullie Circle, NE, Atlanta, GA 30329-2305.
ASME	American Society of Mechanical Engineers, Three Park Avenue, New York, NY 10016-5990.
ASSE	American Society of Sanitary Engineering, 901 Canterbury, Suite A, Westlake, Ohio 44145.
ASTM	American Society for Testing and Materials, 100 Barr Harbor Drive, West Conshohocken, PA 19428-2959.
AWS	American Welding Society, 550 NW LeJeune Road, Miami, FL, 33126.
AWWA	American Water Works Association, 6666 W. Quincy Avenue, Denver, CO 80235.
BSI (BS EN)	British Standard International, 389 Chiswick High Road, London, W4 4AL United Kingdom.
CSA	Canadian Standards Association, 5060 Spectrum Way, Suite 100, Mississauga, Ontario, Canada, L4W 5N6.
IAPMO	International Association of Plumbing and Mechanical Officials, 5001 E. Philadelphia Street, Ontario, CA 91761-2816.
IEEE	The Institute of Electrical and Electronics Engineers, Inc., 445 Hoes Lane, Piscataway, NJ 08854.
ISO	International Organization for Standardization, 1 ch. de la Voie-Creuse, Casa Postale 56, CH-1211 Geneva 20, Switzerland.
MSS	Manufacturers Standardization Society of the Valve and Fittings Industry, 127 Park Street, NE, Vienna, VA 22180.
NFPA	National Fire Protection Association, 1 Batterymarch Park, P.O. Box 9101, Quincy, MA 02169-7471.
NSF	NSF International, 789 Dixboro Road, Ann Arbor, MI 48113-0140.
SAE	Society of Automotive Engineers, 400 Commonwealth Drive, Warrendale, PA 15096.
SRCC	Solar Rating and Certification Corporation, 400 High Point Drive, Suite 400, Cocoa, FL 32926.
UL	Underwriters Laboratories, Inc., 333 Pfingsten Road, Northbrook, IL 60062-2096.

 

(Ord. 2013-0050 § 22, 2013.)